Models
>
BGGF3042KFA
BGGF3042KFA Frigidaire Range - Overview
Sections of the BGGF3042KFA
[Viewing 6 of 6]Manuals & Care Guides for BGGF3042KFA
Click to downloadInstall
Installation Instructions
(0.87MB)
Install
Installation Instructions
(2.95MB)
Install
Installation Instructions
(2.68MB)
Manual
Owner's Manuals
(1.49MB)
Manual
Owner's Manuals
(12.30MB)
Wiring
Wiring Diagram
(0.56MB)
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor
PartSelect #: PS1528542
Manufacturer #: 316490000
This temperature sensor detects the temperature within the oven cavity.
$65.85
In Stock
Light Bulb
PartSelect #: PS12751166
Manufacturer #: 316538904
Clear, 120 Volt, 40 Watt.
$25.08
In Stock
LENS
PartSelect #: PS16218465
Manufacturer #: 5304524341
This lens covers the interior oven light bulb.
$15.66
In Stock
Oven Rack
PartSelect #: PS1765356
Manufacturer #: 316496201
This is a replacement rack for your oven. The oven rack fits into grooves on the side of the oven wall, and acts as a shelf that you can place food items on when you want to cook them in the oven. Thi...
$154.66
In Stock
GLASS
PartSelect #: PS11728351
Manufacturer #: 5304503232
This is also called the heat barrier glass.
$194.33
In Stock
Natural Gas to Liquid Propane Conversion Kit
PartSelect #: PS2351422
Manufacturer #: GRLP3
This kit is used to convert your appliance to liquid propane. This liquid petroleum gas conversion kit contains seven orifices, each under an inch long.
$83.32
In Stock
Oven Rack Link
PartSelect #: PS2364129
Manufacturer #: 316546300
This part is a single oven rack link arm. It is a genuine OEM replacement part for your oven. It connects the oven rack to the door bracket, to allow the rack to extend out when you open the oven door...
$30.62
In Stock
Oven Drawer Handle Screw
PartSelect #: PS1145022
Manufacturer #: 316433303
Order quantity needed.
$22.11
In Stock
Questions And Answers for BGGF3042KFA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the BGGF3042KFA
[Viewing 9 of 9]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bought a new gas oven that did not come with a propane conversion kit.
I followed the simple instructions that were included in the kit. I started by replacing the 5 orifices on the top burners. The orifices are well labeled with numbers and colors. Next, I tightened the broiler burner orifice and the oven burner orifice with a 1/2 inch wrench. I had to tighten them pretty good to get the flame down where it is supposed to be. Then, I checked for leaks and I was then ready to cook.
Parts Used:
-
Denny from Bishop, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench set
123 of 177 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove was set up for natural gas and needed to be converted to LP
The LP conversion kit contained very good, detailed instructions. I replaced the gas orifices, took off the bottom door and adjusted the regulator.
Used the screwdriver to adjust the low flame and everything was done.
Used the screwdriver to adjust the low flame and everything was done.
Parts Used:
-
Ed from Orange, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
117 of 191 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cracked oven door inner glass
Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!
Parts Used:
-
Mitch from Fernandina Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
74 of 112 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!