Models
>
5649600490
5649600490 Kenmore Refrigerator - Overview
Sections of the 5649600490
[Viewing 4 of 4]Keep searches simple, eg. "belt" or "pump".
![Screw - 8-18 x 5/8 – Part Number: WP9741232 Screw - 8-18 x 5/8 – Part Number: WP9741232](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11747050-1-S-Frigidaire-WP9741232-Screw-8-18-x-5-8.jpg)
Screw - 8-18 x 5/8
PartSelect #: PS11747050
Manufacturer #: WP9741232
Sold individually.
$10.11
In Stock
![Terminal Block with Nuts and Washers – Part Number: 400008 Terminal Block with Nuts and Washers – Part Number: 400008](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/2040688-1-S-Frigidaire-400008-Terminal-Block-with-Nuts-and-Washers.jpg)
Terminal Block with Nuts and Washers
PartSelect #: PS2040688
Manufacturer #: 400008
No Longer Available
![Water Inlet Valve – Part Number: WP303650 Water Inlet Valve – Part Number: WP303650](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11740648-1-S-Frigidaire-WP303650-Water-Inlet-Valve.jpg)
Water Inlet Valve
PartSelect #: PS11740648
Manufacturer #: WP303650
This water inlet valve is intended for use with under counter style dishwashers. It has a 3/8 of an inch FPT (female pipe thread) valve and a mounting bracket. - This water inlet valve should be loca...
No Longer Available
Questions And Answers for 5649600490
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 5649600490
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed a tub sound shield
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Parts Used:
-
Carol from REIDSVILLE, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unfortunately, a mouse had made its home on top of our surround insulation. For hygienic reasons, I replaced the surround.
1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.
Parts Used:
-
John from Taylor, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!