Models
>
44-2408-23-01
44-2408-23-01 Tappan Washer - Overview
Sections of the 44-2408-23-01
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
![Water Inlet Valve – Part Number: 134190200 Water Inlet Valve – Part Number: 134190200](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/815509-1-S-Frigidaire-134190200-Water-Inlet-Valve.jpg)
Water Inlet Valve
PartSelect #: PS815509
Manufacturer #: 134190200
This washing machine water inlet valve has two ports for water to enter.
$162.38
In Stock
![Screw – Part Number: 131302800 Screw – Part Number: 131302800](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/417463-1-S-Frigidaire-131302800-Screw.jpg)
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
![Snubber Ring – Part Number: 5308002385 Snubber Ring – Part Number: 5308002385](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/473378-1-S-Frigidaire-5308002385-Snubber-Ring.jpg)
Snubber Ring
PartSelect #: PS473378
Manufacturer #: 5308002385
Mounts at the base under the support.
$51.35
Special Order
![Washer Bolt – Part Number: 137539500 Washer Bolt – Part Number: 137539500](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/3655064-1-S-Frigidaire-137539500-Washer-Bolt.jpg)
Washer Bolt
PartSelect #: PS3655064
Manufacturer #: 137539500
Holds plated on Trunion .312-18 x 1.625.
$23.90
In Stock
![SPACER – Part Number: 5308015493 SPACER – Part Number: 5308015493](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/474201-1-S-Frigidaire-5308015493-SPACER.jpg)
SPACER
PartSelect #: PS474201
Manufacturer #: 5308015493
This spacer goes between the timer knob and the dial.
$18.96
In Stock
![Levelling Leg Pad – Part Number: 131422100 Levelling Leg Pad – Part Number: 131422100](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/417749-1-S-Frigidaire-131422100-Levelling-Leg-Pad.jpg)
Levelling Leg Pad
PartSelect #: PS417749
Manufacturer #: 131422100
Sold Individually.
No Longer Available
Questions And Answers for 44-2408-23-01
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 44-2408-23-01
[Viewing 3 of 3]Leaking
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/815509_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/473382_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/474640_1_S.jpg)
Show All
No hot or cold water
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/815509_1_s.jpg)
Show All
Burning smell
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/459613_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Parts Used:
-
alvaro from east hampton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
86 of 96 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking washing machine.
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops. There were a few pieces. Then sealed it back up with the oil that came with the PartSelect Kit and put it back together. Works great now. No more LEAKS! Yippy.
Parts Used:
-
Ron from Williamsburg, MI
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
24 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt worn causing machine to make all kinds of noise
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!!
working perfectly nice and quite !!!
Parts Used:
-
Kenneth from Baltimore, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
19 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!