36314572000 Kenmore Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The rollers on the upper rack broke
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers out. Place two new rollers in the rail and put the plastic end piece on. Use the hammer and punch to bend the metal clip back into place. Snap the rails on the rack and set the rack on the guides in the dishwasher. Replace the top guide using the screwdriver, you will have to twist the rails in order get them in between the
guides.
guides.
Parts Used:
-
Carl from Fairfield, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
542 of 569 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
Parts Used:
-
Mark from Huntingdon Valley, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
520 of 542 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel broken off bottom rack
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done!
Parts Used:
-
Julie from Maumee, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
500 of 514 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The rear wheels were missing on the lower rack.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
Parts Used:
-
Teresa from Phenix City, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
474 of 486 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken upper rack roller, rack kept falling off the track
Used the pliers to remove the broken roller. It came off in pieces. Slid new one on.
Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.
Cap on end of roller track was a bit of a challenge. It sort of twists & pulls off.
Parts Used:
-
Doug from Columbus, OH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
396 of 404 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rollers fell off lower rack of dishwasher.
First removed four old wheels. then attached four new wheels to lower rack by pressing into slots.
Parts Used:
-
Lloyd from The Villages, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
369 of 371 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stud assembly in the middle of each wheel no longer stayed inside the wheel.
Just pulled off the old wheel. I just had to push in the stud to the wheel and pushed it on to the rack of the dishwasher. Very easy repair! Only disappointing part was that it bothered me to have to purchase the stud with the wheel. I was told they only came as the set. I only needed to purchase that inside stud. My wheels were fine.
Parts Used:
-
Wendy Baldwin from Stowe, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
376 of 394 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rack falling off of upper slides
1. I removed the plastic stops from the ends of the upper rack slides.
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away
2. Removed the upper rack.
3. Unclipped the old rollers from the rack.
4. Clipped the new rollers onto the rack.
5. Made a grunting noise so the wife could hear.
6. Walked away
Parts Used:
-
Eric from Centreville, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
224 of 296 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher wouldn't fully drain
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. This easy repair solved the problem.
Parts Used:
-
Dan from Minnetonka, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
189 of 204 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wheel replacement
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs
most of the parts were for future repairs
Parts Used:
-
michael from perry hall, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
235 of 436 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dish washer is not running through cycles
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...
Parts Used:
-
mike from huntley, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable), Wrench set
93 of 107 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower dishrack rusted
-
michael from Bloomington, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
89 of 98 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wheels were worn out and kept falling off
popped old wheel off popped new one on
for the rack roller i took the ends off and slid old rollers off then slid new ones on.
for the rack roller i took the ends off and slid old rollers off then slid new ones on.
Parts Used:
-
JOHN from PURCELLVILLE, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
78 of 83 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
roller on upper rack broken - lower rack plate holders broken
lower rack took one min. take out old slide in new
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.
upper rack a little tricky had to remove end caps on rack arms to slide rack out to replace rollers. end caps are not snapped in they have a lever in the track that is part of the cap if you twist it a little cap will slide off.
total time for this part 15 min.
Parts Used:
-
charles from canton, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
109 of 189 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
D/W would not drain. Water standing in bottom.
It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.
After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in the wire harness.
I work on a 260 + unit property, as well as working for a property management company who rents single family homes.
PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.
After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in the wire harness.
I work on a 260 + unit property, as well as working for a property management company who rents single family homes.
PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.
Parts Used:
-
Ed from Cornelius, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
65 of 71 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!