Models
>
1196487810
1196487810 Kenmore Wall Oven - Overview
Sections of the 1196487810
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
![Main Terminal Block Kit – Part Number: 5304409888 Main Terminal Block Kit – Part Number: 5304409888](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/471605-1-S-Frigidaire-5304409888-Main-Terminal-Block-Kit.jpg)
Main Terminal Block Kit
PartSelect #: PS471605
Manufacturer #: 5304409888
Terminal blocks (also called terminal boards or strips) provide a convenient means of connecting individual electrical wires.
$11.93
In Stock
![Burner Switch Kit – Part Number: 5303935086 Burner Switch Kit – Part Number: 5303935086](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/470145-1-S-Frigidaire-5303935086-Burner-Switch-Kit.jpg)
Burner Switch Kit
PartSelect #: PS470145
Manufacturer #: 5303935086
This switch controls the stove top surface burner.
$51.03
In Stock
Questions And Answers for 1196487810
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1196487810
[Viewing 5 of 5]Element will not heat
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/470145_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/471605_1_S.jpg)
Show All
Little to no heat when baking
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/471605_1_S.jpg)
Show All
Will Not Start
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/471605_1_S.jpg)
Show All
Oven not heating evenly
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/471605_1_S.jpg)
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/471605_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Parts Used:
-
Timothy from Spring Valley, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
98 of 155 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Parts Used:
-
George from New Port Richey, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
45 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Parts Used:
-
Melvin from Attica, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
23 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!