Models
>
11042922200
11042922200 Kenmore Washer - Overview
Sections of the 11042922200
[Viewing 7 of 7]Manuals & Care Guides for 11042922200
Click to downloadKeep searches simple, eg. "belt" or "pump".
Door Lock Latch
PartSelect #: PS11745016
Manufacturer #: WP8182634
This part is used on front load washers and includes the interlock switch assembly.
$156.47
In Stock
Drain Pump Kit
PartSelect #: PS1485610
Manufacturer #: 280187
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
$225.28
In Stock
Water Inlet Valve
PartSelect #: PS11744913
Manufacturer #: WP8181694
Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$96.05
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.18
In Stock
Shock Absorber
PartSelect #: PS11745030
Manufacturer #: WP8182703
Shock absorbers help keep the washer from vigorous shaking during its cycles. Sold individually.
$65.01
In Stock
Flowmeter
PartSelect #: PS11748313
Manufacturer #: WPW10110225
This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.
$133.54
In Stock
Bellow
PartSelect #: PS11744939
Manufacturer #: WP8181850
Also known as a door boot seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately...
$319.27
In Stock
Temperature Sensor
PartSelect #: PS11755214
Manufacturer #: WPW10467289
This part regulates the temperature of the water in the tub. The sensor is located in the heating element.
$47.46
In Stock
Drive Belt
PartSelect #: PS11754067
Manufacturer #: WPW10388414
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
NOTE: Per Manufacture, belt measures 48.22" long uninstall...
$67.18
In Stock
Bellow to Outer Tub Clamp
PartSelect #: PS11744959
Manufacturer #: WP8182210
Used to help hold your bellow in place on your washer.
$47.00
In Stock
Bellow Clamp
PartSelect #: PS11765855
Manufacturer #: W10902779
This is the replacement bellow clamp for your washer. It approximately 16 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on t...
$41.01
In Stock
Door Hook/Strike
PartSelect #: PS11744910
Manufacturer #: WP8181651
Attaches to door lock mechanism.
$20.79
In Stock
Questions And Answers for 11042922200
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lee
November 30, 2022
SUD displays even when no soap is used then goes through numerous drain and spin cycles for over 20 minutes. I cleaned the drain and pump filter with no change. Thank you for any help
For model number 11042922200
Hello Lee, thank you for contacting us. The SUD display code usually indicates an overdose of detergent, but there could be other culprits of this code. We suggest that you check the drain pump, part number PS1485610, water pressure switch, part number PS11755855, and the electronic control board, part number PS10064572. If you require assistance to place an order, please contact customer service. We hope that helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the 11042922200
[Viewing 13 of 13]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
Parts Used:
-
Donald from Wichita, KS
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Socket set
231 of 243 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
Parts Used:
-
James from Vilonia, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
192 of 231 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tub of front load washer was slowly filling with water when machine was empty/off
Pulled out machine...removed top panel..unscrewed existing valve and removed it...then reversed the whole process with the new valve..it was very easy to do and worked perfectly...no more water in tub!
Parts Used:
-
Andrea from Chelmsford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
140 of 150 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!