This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$47.19
In Stock
Order within the next 3 hrs and your part ships today!
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
$46.08
In Stock
Order within the next 3 hrs and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$8.76
In Stock
Order within the next 3 hrs and your part ships today!
Upper Rack Assembly - T3 PRO. This is the complete upper rack and the wash arm.
$184.93
In Stock
Order within the next 3 hrs and your part ships today!
Questions And Answers for PLD4375RFC0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wayne
September 5, 2022
I get a PF code at the end of the wash and rinse cycle. Dishes are clean.
For model number PLD4375RFC0
Hello Wayne, Thank you for the question. The PF indicates there has been a Power Failure. To reset the appliance, hold the cancel button down for 3 seconds or until the light display disappears or changes. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Annette
December 9, 2022
I have a leak in the inlet value. I'm hoping that is what the part is called. Not sure what part number this would be to replace. If I could have a picture of the hosing and parts attached to it that might help. Thank you for any help you can give on this. If you need serial # TH74093080.
For model number PLD4375RFC0
Hi Annette,
Thank you for your question. The part number listed under your model number for the water inlet valve is PS1524958. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
I need to know the outer height , width and depth of this model.
Thanks,
For model number PLD4375RFC0
Hello Lina, thank you for reaching out. According to our research, the dimensions of your model are approximately:
Height: 34-3/4 inches.
Width: 23-7/8 inches.
Depth: 23 inches.
We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.