This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.
$34.74
In Stock
Order within the next 6 hrs and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
Order within the next 6 hrs and your part ships today!
This dryer drum drive motor with pulley for drum belt has reverse threads for the blower wheel. This is a genuine OEM part.
$312.02
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for EFMG617STT0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pat
June 26, 2023
Dryer will not start after programming drying cycle. When I open the door the internal light does not come on
For model number EFMG617STT0
Hello Pat, thank you for reaching out. We have researched the model and would suggest checking the power cord and wiring. Reset the dryer by unplugging it for a minute and then plugging back in. If this does not solve the issue, the problem might be with the user interface control board, part number PS11766152. It processes the cycle settings you choose. Checking the control board for continuity using a multimeter might help. Good luck with the repair!
Hello
Our dryer has recently been putting a grate type mark on some clothing as well as eating some clothing. It appears the grille feels rough to the touch as well appears to have a charcoal look to it. Is it possible to replace this? I tried sanding it but this doesn’t work. Thank-you
For model number EFMG617STT0
Hello Grace, thank you for contacting us. Replacing the grill assembly may fix the issue, it is part number PS11766055. You may follow these instructions to replace the grill assembly. These may not be of the exact model, but will help you with the replacement:
Un-thread the screws securing the filter cover and remove it. Pull out the filter. Depress the tabs to release the filter holder from the cover. Now the grill assembly is free to replace. You may follow these steps backwards to install the new grill assembly.
Glad to be of assistance!
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
1. Pry Dryer top up and off the clips. (Front of Dryer) 2. Remove 2 phillips screws on the inside of front panel. 3. Lift front panel up and set off to the side 4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place. 5. Unplugged and removed both coils, installed new coils and bracket. Re installed front panel, screws and top.